Sometimes you need to do two things at once. For example you might want to blink an LED while reading a button press. In this case, you don't want to use delay(), because Arduino pauses your program during the delay(). If the button is pressed while Arduino is paused waiting for the delay() to pass, your program will miss the button press.

This sketch demonstrates how to blink an LED without using delay(). It turns on the LED on and then makes note of the time. Then, each time through loop(), it checks to see if the desired blink time has passed. If it has, it toggles the LED on or off and makes note of the new time. In this way the LED blinks continuously.

An analogy would be warming up a pizza in your microwave, and also waiting some important email. You put the pizza in the microwave and set it for 10 minutes. The analogy to using delay() would be to sit in front of the microwave watching the timer count down from 10 minutes until the timer reaches zero. If the important email arrives during this time you will miss it.

What you would do in real life would be to turn on the pizza, and then check your email, and then maybe do something else (that doesn't take too long!) and every so often you will come back to the microwave to see if the timer has reached zero, indicating that your pizza is done.

In this tutorial you will learn how to set up a similar timer.

Arduino Board LED Resistor, anything between 220 ohm to 1K ohm Circuit

To build the circuit, connect one end of the resistor to Arduino pin 13. Connect the long leg of the LED (the positive leg, called the anode) to the other end of the resistor. Connect the short leg of the LED (the negative leg, called the cathode) to the Arduino GND, as shown in the diagram above and the schematic below.

Most Arduino boards already have an LED attached to pin 13 on the board itself. If you run this example with no hardware attached, you should see that LED blink.

Schematic:

click the image to enlarge

image developed using Fritzing. For more circuit examples, see the Fritzing project page

After you build the circuit plug your Arduino board into your computer, start the Arduino IDE, and enter the code below.

The code below uses the millis() function, a command that returns the number of milliseconds since the Arduino board started running its current program, to blink an LED.

/* Blink without Delay
 
 Turns on and off a light emitting diode(LED) connected to a digital  
 pin, without using the delay() function.  This means that other code
 can run at the same time without being interrupted by the LED code.
 
 The circuit:
 * LED attached from pin 13 to ground.
 * Note: on most Arduinos, there is already an LED on the board
 that's attached to pin 13, so no hardware is needed for this example.
 
 
 created 2005
 by David A. Mellis
 modified 8 Feb 2010
 by Paul Stoffregen
 
 This example code is in the public domain.
 
 
 http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay
 */
 
// constants won't change. Used here to 
// set pin numbers:
const int ledPin =  13;      // the number of the LED pin
 
// Variables will change:
int ledState = LOW;             // ledState used to set the LED
long previousMillis = 0;        // will store last time LED was updated
 
// the follow variables is a long because the time, measured in miliseconds,
// will quickly become a bigger number than can be stored in an int.
long interval = 1000;           // interval at which to blink (milliseconds)
 
void setup() {
  // set the digital pin as output:
  pinMode(ledPin, OUTPUT);      
}
 
void loop()
{
  // here is where you'd put code that needs to be running all the time.
 
  // check to see if it's time to blink the LED; that is, if the 
  // difference between the current time and last time you blinked 
  // the LED is bigger than the interval at which you want to 
  // blink the LED.
  unsigned long currentMillis = millis();
 
  if(currentMillis - previousMillis > interval) {
    // save the last time you blinked the LED 
    previousMillis = currentMillis;   
 
    // if the LED is off turn it on and vice-versa:
    if (ledState == LOW)
      ledState = HIGH;
    else
      ledState = LOW;
 
    // set the LED with the ledState of the variable:
    digitalWrite(ledPin, ledState);
  }
}